wall bracket Double Holder
Organize your Hand and Body Care products in a decorative wall bracket that fits perfectly two full-sized 500ml 16.91 fl.oz. cosmetics.
The ZENOLOGY wall brackets have a factory cured powder coated finish formulated and applied to give decorative finish, durability and lasting resistance to ordinary cleaning, abrasion and scuffing.
The ZENOLOGY Wall Bracket is exclusively designed, manufactured and assembled in Sweden. We source our raw material from local suppliers and we use AISI 304 in combination with powder coated finish. Testing our product’s mechanical durability is essential to get insights in our product’s potential weaknesses and to ensure ideal performance. Our products are put in mechanical endurance tests, salt spray test, chemical resistance analysis, FEM-analysis, to push the durability to its limits and assure sustainability over time.
Q: How do I maintain and care for the wall bracket?
A: Please find here the recommended care and maintenance schedules. Inspect your products each and every 3-6 months and clean more regularly if required. Rinse the surfaces with clean fresh water after cleaning to remove all daily residues.
- Carefully remove any loose surface deposits with a wet sponge or light nylon brush.
- Clean by gently rubbing the surface with a soft brush (non-abrasive) and a dilute solution of a mild detergent, e.g. pH-neutral liquid hand or dishwashing detergent in warm water to remove dust, salt and other deposits. For stubborn stains use only recommended solvents on the affected area, e.g. Isopropyl alcohol (IPA) or methylated spirits, and rinse off with clean water. Do not use other aggressive solvents.
- Rinse the surfaces with clean fresh water after cleaning to remove all residues.
▪Do not use an abrasive material, harsh cleanser, or any cleanser containing chemical detergents or acids.
▪ Do not use turpentine, white spirits, thinners, citrus-based cleaners, or other aggressive solvents on powder coating.
Q: When cleaning the wall bracket, which cleaning products should I avoid?
A: Do not use an abrasive material, harsh cleanser, or any cleanser containing chemical detergents or acids. Do not use turpentine, white spirits, thinners, citrus-based cleaners, or other aggressive solvents on powder coating.
Q: Is the wall bracket only suitable for ZENOLOGY packaging?
A: Yes, this wall bracket is made to measure to fit perfectly our signature 500 ml packaging made of 100% Post-Consumer recycled PET bottle with BIO additive.
Q: Can you wall mount the wall bracket without drilling?
A: Yes, this wall bracket can be mounted to the wall with the Tape Method. See instructions on how to do this. The strong tape will make sure your wall holder for your 500 ml cosmetics will hold safely.
Q: Will the wall bracket damage the wall?
A: Technically speaking, mounting a wall bracket will damage the wall because they must be drilled to make holes when using the screw method. No problem if you don’t mind the holes in your wall. The Tape method can be a solution to avoid drilling.
Q: Does the wall bracket come with matching screws?
A: Yes, the wall bracket for your cosmetics will come with a set of screws.
Q: What material is the wall bracket made off?
A: The ZENOLOGY Wall Bracket is exclusively designed, manufactured, and assembled in Sweden. We source our raw material from local suppliers, and we use stainless steel. AISI 304 in combination with powder coated finish in matt black color
Q: What is AISI 304?
A: The ZENOLOGY Wall Bracket is made of AISI 304 also known as chromium-nickel stainless steel. It has strength and very good formability, while it is also highly anti-corrosion, so perfect for wet areas like the bathroom and kitchen, places to use our cosmetics. Typical uses of 304 stainless steel include sinks, and kitchen equipment such as pans, tubing, and much more.
Q: How to install the wall bracket?
A: There are two was to install the wall bracket, the screw method and the tape method.
the screw method:
a. Apply bracket level to the wall, measure 48”/120 cm from floor to bottom of bracket.*
b. Mark drill holes with pencil.
c. Drill holes, drill depth minimum 40 mm
d. Insert wall anchors into hole by carefully tapping with hammer.
e. Clean all surfaces with included alcohol wipe and dry thoroughly prior to installation to remove any greasy residue.
f. Peel off backing of adhesive strip on bracket.G. Aim the bracket towards the drill holes, press entire bracket to wall and ensure tape has adhered to surface.
h. Install with included screws through the bracket in to the wall anchors.
i. Place the Spaza key in the key slot. Move the hook aside, place the bottle and swing back the hook around the cap.
the tape method:
a. Measure 48 inches (120 cm) from oor to top of bracket and mark position with pencil or piece of masking tape.*
b. Clean all surfaces with included alcohol wipe and dry thoroughly prior to installation to remove any greasy residue.
c. Peel off backing of adhesive strip on bracket. Aim the bracket towards the wall in level. Press entire bracket against wall for 60 seconds to ensure bracket has adhered to surface.
d. Apply a thin bead of bathroom-grade sealant around the edge of each bracket unit. B. Install cover plugs in the bracket screw holes.
e. Leave bracket on the wall for at least 24 hours before use. For best result 48 hours.
f. Place the Spaza key in the key slot. Move the hook aside, place the bottle and swing back the hook around the cap.